Please wait a minute...
All
Member of CSTAM
 
 
Dynamics>>More
Table of Content
10 February 2000, Volume 22 Issue 1
For Selected: Toggle Thumbnails
    Research paper
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-002
    Abstract ( 804 )  
    Several fluid mechanics problems involving reservoir engineering and production engineering where horizontal wells are used to produce oil are discussed in the present paper, such as,the calculation of production of a horizontal well, the unsteady well test and flow field analysis ofa horizontal well, the effect of pressure drop along wellbore on production of a horizontal well, andthe fluid flow couple both in wellbore and the reservoir near well, and so on. It is suggested that themechanism of horizontal ...
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-003
    Abstract ( 816 )  
    The recent research results on robust design are reviewed and some robust design methodsare introduced as well. Robust design for structures is proposed firstly. A truss structural exampleshows that this new method is much better than current design method. The prospect of this methodfor ship hull structures is also predicted.
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-004
    Abstract ( 864 )  
    Based on the blasting softening technology for hard top coal in long-wall top coal caving, asimple fractal model of rock fracture is establishedto deal with dissipated energy of rock fracture andfractal dimension of rock fragmentation and to obtain the theoretical relation between the fractal dimension of rock fragmentation and explosive specific charge. The blasting experiment of simulationmaterial model is conducted to verify theoretical results. Taking the fractal dimension of crack distribution on the ...
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-005
    Abstract ( 953 )  
    in this paper, tile Simple Cell Mappingtheory (SCM) is used to compute strange attractors in the forced responses of the damped Duffingoscillator with some parameters. The solution procedure and results show that the SCM is simple andeffective for global solution of the system.
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-006
    Abstract ( 779 )  
    Under the rough road exciting, the largedynamic stress will result in fatigue of the chassis.By the statistical analysis for the dynamic strainsignal of a heavy truck's chassis, a simple dynamicstrength analysis method t based on the 3 probability of the key measured points' dynamic stress, isput forward in this paper.
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-007
    Abstract ( 865 )  
    The calculation of wheel/rail threedimensional elasto-plastic contact stress is the basisfor the research on wheel/rail contact fatigue. Thepaper first combines CONTACT program with finiteelement method, taking into account the real geometry and boundary conditions of rail, proposes aunited wheel/rail rolling contact numerical methodand computer software CMEF, which can calculatethe real elasto-plastic stress field of rail effectively.
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-008
    Abstract ( 733 )  
    The electromagnetic and mechanicalcoupling properties of REGMM rods are discussed.The physical model of the coupling system for theinspecting apparatus is established and the equivalent circuits for the coupling system is derived bymeans of resistance analysis method. The electricaland mechanical parameters of the TbxDy1-xFe2-z.(0.27 0.3, 0 5 0.1) rods such as magnetostrictive strain, Young's modulus, magnetomechanical coupling coefficient under electromagneticand mechanical stress fields are obtained wit...
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-009
    Abstract ( 786 )  
    in this paper, based on the unifiedstrength theory, a plane strain axisymmetric problem under the state of the elasto-viscoplasticity wasanalyzed and a unified solution was obtained, fromwhich a set of solutions can be obtained based ondifferent strength theories from the Mohr-coulombstrength theory to the twin shear strength theory.The results in the references are only the special solutions. By using the Unified Strength Theory, themore proper solution about different materials canbe derived.
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-010
    Abstract ( 804 )  
    On the basis of investigation on the influence of internal upset transition geometry on thestress concentration of a drill pipe, basic design requirements for a drill pipe with low stress concentration were proposed. Full size fatigue tests werecarried out to verify that analytically designed upsettaper geometry has a good performance. The workin this paper provides important basis for improvinginternal upset taper design of a drill pipe.
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-011
    Abstract ( 781 )  
    An element stiffness matrix of the circular curved beam is presented by using force method,Which is used to calculate the circular curved continuous beams by the matrix displacement method.It is based on a clear mechanical concept, can beprogrammed easily, and used by designer.
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-012
    Abstract ( 1161 )  
    In this paper, a two-dimensionalanatomically-based biodynamic model of the humanlower extremity is established. The hip joint is modelled as a passive-joint torque with effects of viscoelastic structures situated across the joint. Alsoan anatomical model of the knee joint is establishedin the paper. In addition to the knee ligaments, themodel includes the effects of five significant musclegroups involved in the motion of the lower limb. Thenumerical results give the forces associated with themuscle groups a...
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-013
    Abstract ( 769 )  
    in this paper, an AUSM+ scheme in conjunction with the third-order MUSCL scheme is developed for the multidimensional hyperbolic conservation laws in curvilinear coordinates. The presentscheme combined with the Runge-Kutta scheme isapplied to Two-dimensional transonic and supersonic inviscid flow in the cascade built of two circulararc blades. The accuracy has been assessed by comparing the results with the other numerical resultsavailable in literature. The results given in this paper show that the present...
    2000, 22(1):  0-0.  doi:10.6052/1000-0879-f2000-014
    Abstract ( 837 )  
    A Lattice Boltzmann model for onedimensional unsteady open channel flows is established, by analyzing the multi-scale equations of theLB method and the one-dimensional shallow waterequations. One-dimensional dam break, a classical and practical problem, is simulated by the LBscheme. The good agreement of LB results withthe results of implicit Preissmann scheme and theanalytical solution shows that the LB method isa feasible and accurate approach to simulate onedimensional unsteady open channel flows in engi...