All
Member of CSTAM
 
 
Dynamics>>More
Archive By Subject
Content of Around the mechanics in our journal
Published in last 1 year |  In last 2 years |  In last 3 years |  All
Please wait a minute...
For Selected: Toggle Thumbnails
THE PROGRESS OF STUDIES OF UNCOMMANDED MOTION AND ITS SUPPRESSION OF FLYING VEHICLE WITH HIGH MANUEVERABILITY
DENG Xueying, ZHU Jun, WANG Yankui, MA Baofeng
Mechanics in Engineering    2012, 34 (3): 1-8.   DOI: 10.6052/1000-0879-12-060
Abstract1277)      PDF(pc) (1310KB)(865)       Save
High maneuver ability might be achieved by a flying vehicle at high angles of attack. The uncom-manded motions of aircraft can be generated at high angles of attack in flying with high maneuver ability. Therefore this problem should be considered in the early phase of aircraft design and the complicated flow behaviors and characteristics of uncommanded motions of the designed configuration will be studied to reveal the dominant flows to drive uncommanded motions. The flow control techniques are developed to suppress the uncommanded motions. In the present paper it is pointed out that the forebody asymmetric vortices are very sensitive to the micro-perturbation on the model nose. For a long time it is wrongly believed that the forebody asymmetric vortex flow is non-deterministic. It is found that if a micro-manual-perturbation is added on the nose tip of model the asymmetric vortex flow can be reproduced. Based on the manual-perturbation technique the evolution of the asymmetric vortices related with the circumferential angle of perturbation is revealed. The dominant flows are discovered, which drive the uncommanded motions of two typical configura-tions. The perturbation control techniques are developed to suppress those uncommanded motions by rotating the tip-perturbation and setting tip-perturbation on a proper location to make two pair of asymmetric vortices in the phase reversal. The micro-perturbation plays a very important role in the non-liner separated and vortex flows at high angles of attack. The roles of micro-perturbation are the key in controlling the non-linear vortex flows, which drive the uncmmande motions.
Reference | Related Articles | Metrics
Cited: Baidu(3)
THE CHARACTERISTICS OF DAMAGE CAUSED BY IMPACT ON THE WHIPPLE SHIELD OF LOW-DENSITY BRITTLE MICRO-METEOROID
ZHU Dangdang, PANG Baojun, CHEN Haibo, JIA Bin
Mechanics in Engineering    2012, 34 (3): 9-11,28.   DOI: 10.6052/1000-0879-11-331
Abstract1063)      PDF(pc) (7635KB)(1049)       Save
In this paper, numerical impact experiments on spacecraft typical Whipple shield with silicate pro-jectile as low-density brittle micro-meteoroids are carried out to obtain a low-density brittle micro-meteoroids' damage mode and damage law. It is shown that when the projectile impact velocity is between 1.1 km/s and 1.4 km/s, the front plate injury model changes from the petal-type cracking into the hole, when the speed is 1.4 km/s the cracks appear on the drum header. With the increase of the projectile speed, flakes occur on the back plate, and the petal-type crack is formed. When the projectile impact speed is 1.95 km/s, the back plate cracks into the hole, leading to the destruction of protective structures.
Reference | Related Articles | Metrics
APPLICATION OF MESH-LESS METHOD IN ANALYSIS OF ELASTIC-PLASTIC STABILITY OF AN EDGE SLOPE
WEI Demin, HU Yuanzhe, JIANG Xueling
Mechanics in Engineering    2012, 34 (3): 12-17.   DOI: 10.6052/1000-0879-11-169
Abstract821)      PDF(pc) (1759KB)(994)       Save
The element-free Galerkin method(EFGM) is applied to solve the elastic-viscoplastic problems in this paper. The corresponding computational program is written and applied to the elastic-plastic stability analysis of the edge slope. The comparisons and analyses of the numerical results of EFGM and FEM show that EFGM for elastic-viscoplastic problems is effective with good computational stability and convergence.
Reference | Related Articles | Metrics
Cited: Baidu(1)
MECHANICAL ANALYSIS OF WHOLLY GROUTED ANCHOR IN ROCK SLOPE
GUO Yongjian, SUN Yang
Mechanics in Engineering    2012, 34 (3): 18-22.   DOI: 10.6052/1000-0879-12-024
Abstract972)      PDF(pc) (969KB)(1187)       Save
Based on the Mindlin's solution of displacement for a concentrated force in space, combined with the well assumed mechanical characteristic form of the wholly grouted anchor in a joint plane, with the sliding force as a concentrated force, the formulas for the axial force and the shearing stress along the anchor are obtained. With them applied to rock slopes, the axial force and the shearing stress along the bolt for rock slopes of rock mass of different types are obtained.
Reference | Related Articles | Metrics
Cited: Baidu(3)
ANALYSIS ON STRUCTURE AND THERMAL STABILITY OF GOLD NANOWIRE COVERED ON THE SURFACE OF CARBON NANOTUBE
ZHANG Xingwang, GU Chengjun
Mechanics in Engineering    2012, 34 (3): 43-47.   DOI: 10.6052/1000-0879-11-074
Abstract1258)      PDF(pc) (2899KB)(1032)       Save
In this paper, we study the structure and the thermal stability of gold atoms covered on the surface of carbon nanotubes by molecular dynamics simulations. It is shown that, diversiform stable structures can form on the surfaces of carbon nanotubes: when the density of gold atoms covered on the surfaces of carbon nanotubes is less than 15.91, gold atoms would form gold nanoparticles, when the density is between 15.91 and 104.98, gold atoms would form a series of cylindrical and helical shell structures, when the density is greater than 104.98, gold atoms would have the face centered cubic structure like the crystalline bulk gold. Further more, we have also studied the thermal stability of the helical shell nanowires with the carbon nanotubes' support. The results show that the melting point of the helical shell nanowires with the carbon nanotubes' support is lower than the gold nanowires formed in a free space, but higher than that of the gold nanoparticles.
Reference | Related Articles | Metrics
Mechanics in Engineering    2012, 34 (3): 65-67.   DOI: 10.6052/1000-0879-11-208
Abstract1206)      PDF(pc) (3065KB)(971)       Save
Reference | Related Articles | Metrics
Mechanics in Engineering    2012, 34 (3): 84-85.   DOI: 10.6052/1000-0879-20120321
Abstract600)      PDF(pc) (1961KB)(751)       Save
Related Articles | Metrics
Mechanics in Engineering    2012, 34 (3): 95-101.   DOI: 10.6052/1000-0879-20120325
Abstract971)      PDF(pc) (2332KB)(925)       Save
Reference | Related Articles | Metrics
Mechanics in Engineering    2012, 34 (3): 102-103.   DOI: 10.6052/1000-0879-20120327
Abstract638)      PDF(pc) (328KB)(560)       Save
Related Articles | Metrics
A SURVEY OF AUTONOMOUS NAVIGATION FOR DEEP SPACE EXPLORATION
LI Junfeng, CUI Wen, BAOYIN Hexi
Mechanics in Engineering    2012, 34 (2): 1-9.   DOI: 10.6052/1000-0879-20120201
Abstract1940)      PDF(pc) (3364KB)(1022)       Save
Due to the advantages of reducing the burden of ground station support, enhancing the viability and expanding the special application of spacecraft, autonomous navigation has been successfully validated and begun to apply in foreign deep space missions. It will be a key technology for deep space missions in future. As the lack of ground station tracking resources, the development of autonomous navigation will become more important for Chinese deep space exploration program. Based on the upcoming Chinese Mars mission and asteroids mission, the application and development of autonomous navigation for deep space mission is reviewed and analyzed. Then, the optical sensor used in autonomous navigation system of different deep space mission is recapitulated. Finally, according to the asteroids based optical autonomous navigation of "Deep Space 1" mission, the critical techniques associated with its study of autonomous navigation are summarized.
Reference | Related Articles | Metrics
Cited: Baidu(6)
THE APPLICATIONS OF SHAN-CHEN-TYPE LATTICE BOLTZMANN METHOD IN MICROFLUIDICS SIMULATION STUDY
ZHANG Renliang, DI Qinfeng, WANG Xinliang, DING Weipeng, GONG Wei
Mechanics in Engineering    2012, 34 (2): 10-18.   DOI: 10.6052/1000-0879-20120202
Abstract2008)      PDF(pc) (3154KB)(925)       Save
In a numerical simulation of microscale flow, it is difficult to reasonablly handle the interaction between microscopic particles and to improve computational efficiency. This paper discusses the Shan-Chen-type lattice Boltzmann method and its implementation. The applications of the model in various microfluidic situations are reviewed, and the effectiveness of the model is analyzed. The simulations show that Shan-Chen-type lattice Boltzmann method is easy to be implemented with the micro force and has capability and efficiency in computational microfluidics, and its applications are prospected. At the same time, because of easiness in dealing with wettability boundary, Shan-Chen-type lattice Boltzmann method has experienced tremendous advances in microstructure simulation with slip effect.
Reference | Related Articles | Metrics
Cited: Baidu(3)
APPLICATION OF NEURAL NETWORK IN THE DETERMINATION OF THE MECHANICAL STRENGTH OF WHEAT STRAW
WU Zhengjia, LUO Yuesheng, LIN Pan, ZHU Xiaoqin
Mechanics in Engineering    2012, 34 (2): 58-60,63.   DOI: 10.6052/1000-0879-20120211
Abstract840)      PDF(pc) (1136KB)(882)       Save
To avoid the repeated mechanical experiments to determine the mechanical strength of wheat straw stalk, the neural network technology is adopted to build the prediction model for the mechanical strength of wheat straw stalk using neural network multiple geometric parameters. The prediction results show that the method is effective.
Reference | Related Articles | Metrics
Cited: Baidu(3)
CALCULATION AND TEST OF NATURAL FREQUENCIES FOR SERIES TORSIONAL VIBRATION ABSORBER
CHEN Chao
Mechanics in Engineering    2012, 34 (2): 61-63.   DOI: 10.6052/1000-0879-20120212
Abstract1204)      PDF(pc) (805KB)(882)       Save
Experiments are carried out to obtain transfer functions for torsional vibration absorber (TVA). The natural frequencies of TVA are deduced for different test methods. The calculation results of different test models are compared with accurate values, and good agreements are found.
Reference | Related Articles | Metrics
Mechanics in Engineering    2012, 34 (2): 103-104.   DOI: 10.6052/1000-0879-lxysj2012-160
Abstract915)      PDF(pc) (216KB)(822)       Save
Related Articles | Metrics
ACCOMMODATION THEORIES AND MECHANICAL PROPERTIES OF HUMAN LENS
SONG Fan, ZHAO Xiyu, DU Ruiqi, WEI Jiachen, XU Xianghong
Mechanics in Engineering    2012, 34 (1): 1-9.   DOI: 10.6052/1000-0879-20120101
Abstract2595)      PDF(pc) (3551KB)(992)       Save
As the core component of optical system, human lens accommodation is realized through the cooperation of ciliary, zonular and lens itself. Ciliary dragging the connected zonular leads to the lens deformation change which finally alters optical power. Through this process, light can focus on the retina and result in visual sense. Actually, lens accommodation is a mechanical process that affects visual quality and the prevalent eye degenerative diseases-presbyopia. This paper illustrates various lens accommodation theories as well as their developments, and also summarizes the mechanical properties of lens.
Reference | Related Articles | Metrics
Cited: Baidu(2)
REVIEW ON COMPUTATIONAL EXPLOSION MECHANICS
NING Jianguo, WANG Meng
Mechanics in Engineering    2012, 34 (1): 10-19,69.   DOI: 10.6052/1000-0879-20120102
Abstract1717)      PDF(pc) (4621KB)(1568)       Save
Exact solution of explosion problem cannot be achieved in most cases because of its strong nonlinearity. And data gained from experiments are very limited because explosion is a strong physical course finished in short duration. Simulation of explosion mechanics and related research has greatly promoted rapid development of both explosion mechanics and weaponry. This paper mainly reviews on explosion mechanics, dynamic constitutive model of material and related engineering applications.
Reference | Related Articles | Metrics
Cited: Baidu(14)
SIMULATION BASED ON DISCRETE ELEMENT METHOD AND EXPERIMENT ON FLOW AND PACKING BEHAVIOR OF PARTICLES
LI Wanyi, ZENG Pan, LEI Liping, LIN Dachao
Mechanics in Engineering    2012, 34 (1): 20-26.   DOI: 10.6052/1000-0879-20120103
Abstract1317)      PDF(pc) (2179KB)(613)       Save
The particle flow and packing is an important issue in engineering. In this paper, a series of experiments are designed to measure the physical parameters of particles, such as density, restitution coefficient, friction coefficient and stiffness coefficient. With the hoisting bucket of the blast furnace top in view, the flow behavior of mono-sized particles is simulated by discrete element method (DEM). Results show that the force distribution in the discrete particles is non-uniform, and the strong force chains are parallel to the surface of the left inferior part of the hoisting bucket. A hoisting bucket experimental model with adjusting devices is established for experiments. It is shown that experimental results agree well with DEM results.
Reference | Related Articles | Metrics
Cited: Baidu(6)
SIZE-DEPENDENCE OF SHEAR MODULUS OF A DRYING PARTICULATE FILM FABRICATED BY CONTROLLED VERTICAL DRYING DEPOSITION
CAO He, LAN Ding, WANG Yuren
Mechanics in Engineering    2012, 34 (1): 27-30.   DOI: 10.6052/1000-0879-20120104
Abstract827)      PDF(pc) (1251KB)(482)       Save
In our previous work, we reported that the initial crack spacing depends on the colloidal particle size. However, crack patterns must be related to the mechanical properties of the drying films, which has not been sufficiently explored. The fracture theories for drying colloidal films and the crystal fracture theory are used in this paper to study of a drying film formed by the controlled vertically drying deposition. We found that the shear modulus also depends on colloidal particle size. Further more, comparing our results with the variation of the dry particulate film's shear modulus, a remarkable discrepancy is found for this size-dependant behavior while the particle radius decreases. This remarkable discrepancy shows that the mechanical behaviors of drying particulate films are determined not only by the structure of the solid part but also by the liquid part.
Reference | Related Articles | Metrics
THE FORMATION OF WIND PROFILE IN ENVIRONMENT SIMULATION LABORATORY
ZENG Bo, ZHANG Hongyan, MENG Qinglong
Mechanics in Engineering    2012, 34 (1): 31-34.   DOI: 10.6052/1000-0879-20120105
Abstract906)      PDF(pc) (1217KB)(640)       Save
The numerical simulation and the experimental test are used to investigate the formation of the wind profile of the neutral atmospheric surface layer by screens in the environment simulation laboratory. Taking the screen layout program with variations of porosity of screens as a guide, 30 meshes and 16 meshes with fixed porosity of screens with respective heights of four screen layer collocations are selected. The complex screens are simplified as the porous media model and the k-εvarepsilon model in using the software Fluent. The results show that the screens can be simulated with the porous media and the wind profile can be formed by the compounding of fixed porosity screens in a short experimental section. The simulation results agree well with those of experiment.
Reference | Related Articles | Metrics
Cited: Baidu(1)
STUDY ON THE AIRCRAFT INTEGRATED CHARACTERS WITH DIFFERENT HEIGHT WINGLETS
ZHANG Jianjun, QIAN Guangpin, YANG Shipu, SI Jiangtao
Mechanics in Engineering    2012, 34 (1): 35-38,30.   DOI: 10.6052/1000-0879-20120106
Abstract1143)      PDF(pc) (1367KB)(596)       Save
This paper considers the wingbody shape with two different types of winglets (the blended winglet and shark winglet) by discretized Reynolds average Navier-Stokes equation and the aero-structure coupled equation. The impact of the different heights of the winglet on the lift-drag ratio, the displacement of the wing pressure center, the weight and the flutter character is studied. The results show that the weight increase of the aircraft structure is smaller than the weight increase of effective loads and that the flutter velocity decrease is adjustable within the safety range. Therefore, it is suggested that the selection of the winglet height should have a priority over the lift-drag ratio character during the trade off between aero and weight & flutter in order to have a good drag reduction.
Reference | Related Articles | Metrics
Cited: Baidu(1)
ANALYTICAL SOLUTION FOR BENDING OF SIMPLY SUPPORTED FUNCTIONALLY GRADED BEAM SUBJECTED TO UNIFORM PRESSURE
LI Huadong, ZHU Xi, MEI Zhiyuan, ZHANG Yingjun
Mechanics in Engineering    2012, 34 (1): 39-47.   DOI: 10.6052/1000-0879-20120107
Abstract1624)      PDF(pc) (2063KB)(858)       Save
Based on the semi-inverse stress function method, an analytical solution is obtained for bending of simply supported functionally graded beam subjected to uniform pressure with arbitrary property distribution across the thickness, including explicit analytical expressions of the stress, strain and displacement. Firstly, the system of partial differential equations for the stress function is established based on the fundamental equations for plane stress states, and the expressions of streses are obtained according to the boundary conditions for stresses. Then, the distributions of strains and displacements are obtained according to the constitutive relations of functionally graded materials and displacement boundary conditions. Finally, the proposed solution is validated by comparing the degenerated results for a homogeneous isotropic beam to the classic elastic solution. The distributions of stresses and displacements obtained in this paper are for the functionally graded beam whose material properties obey a power law distribution of the constituent volume fraction, and the effects of top-bottom surfaces'Young's modulus ratio λ and volume fraction exponent n on the variation of the stresses and displacements of the functionally graded beam are discussed.
Reference | Related Articles | Metrics
Cited: Baidu(3)
COMPUTER SIMULATION OF DEFLECTION CURVE SHAPE FOR THE SLENDER, FLEXIBLE, COMPRESSED BAR AFTER BUCKLING
PAN Wenbo, LI Yinshan, LI Tong, LI Xinye
Mechanics in Engineering    2012, 34 (1): 48-51.   DOI: 10.6052/1000-0879-20120108
Abstract1164)      PDF(pc) (960KB)(716)       Save
A Maple code is developed for the slender, flexible, compressed post-buckling bar. Its deformation curve shape is numerically simulated. Simulations and detailed solutions are given for two cases---the maximum deflection and the closing deflection curve after buckling. Mechanical character of instability after buckling is analyzed and computed. Analysis expression is given; the geometric features of the curve in the equilibrium case after buckling is analyzed and computed. The results indicate that the maximum deflection after buckling and the closing deflection curve are two completely different buckling states.
Reference | Related Articles | Metrics
Cited: Baidu(1)
THE UNCERTAIN MODELING AND VALIDATION FOR A CANTILEVER WITH FLEXIBLE ROOT
CHEN Xueqian, XIAO Shifu, LIU Xin'en, WANG Yujun
Mechanics in Engineering    2012, 34 (1): 52-56.   DOI: 10.6052/1000-0879-20120109
Abstract1084)      PDF(pc) (1311KB)(657)       Save
There are some flexibility and uncertainty in the root of a cantilever with bolt joints. The dynamic equation and the approximate result of the cantilever with flexible parameters are presented in the paper. At the same time, in order to study the uncertainty modeling, the translation and rotation flexible parameters are chosen as the uncertain parameters. Then the flexible parameters are identified according to some modal test results. The mean and standard deviations of flexible parameters are obtained by analyzing the identified results subjected to the normal distribution assumption. The mathematical models of the uncertain parameters varying with the pre-torque are built. The models are validated by other modal test results, and the applicable ranges of the models are obtained according to the results.
Reference | Related Articles | Metrics
Cited: Baidu(4)
PRIMARY RESONANCE OF BEAMS ON ELASTIC FOUNDATIONS SUBJECTED TO LATERAL LOADS
WANG Lianhua, MA Jianjun, LIU Qijian
Mechanics in Engineering    2012, 34 (1): 57-61.   DOI: 10.6052/1000-0879-20120110
Abstract1215)      PDF(pc) (1434KB)(672)       Save
The nonlinear vibration of finite-length beams on the Winkler foundation subjected to the lateral loads is investigated. Based on the Winkler foundation model and the Euler-Bernoulli beam theory, the nonlinear in-plane motion equation of the finite-length beam on the Winkler foundation is obtained. The approximate solution of the finite-length beam for the case of the primary resonance is obtained by the Galerkin method and the method of multiple scales. To illustrate the characteristics of the primary resonance, the effects of major parameters on the frequency-response curves of the beam on the elastic foundation are studied, such as, the slenderness ratio, the stiffness coefficient of the foundation, the amplitude of the excitation and the damping coefficient. Comparing with the non-resonant response of the beam, the effect of the primary resonance on the actual dynamic response is analyzed. The numerical results show that the frequency-response curves of the beam have jump and delay; the damping term plays a very important role in the primary resonance of the beam, the primary resonance significantly increases the amplitude of the steady state response.
Reference | Related Articles | Metrics
Cited: Baidu(1)
APPLICATION OF SYMBOLIC COMPUTATION IN NATURAL VIBRATION ANALYSIS OF CABLES AND SUSPENDERS
LIU Zhijun, RUI Xiaoting, YANG Haigen
Mechanics in Engineering    2012, 34 (1): 62-65.   DOI: 10.6052/1000-0879-20120111
Abstract1112)      PDF(pc) (1180KB)(533)       Save
A sufficiently high computational accuracy is achieved by symbolic computation to obtain a high precision solution for the frequency equation and the numerical calculation for mode functions of cables and suspenders fixed at one or two ends. Based on practical examples, the influence of boundary conditions on vibration modes of cables and suspenders is comparatively analyzed.
Reference | Related Articles | Metrics
Cited: Baidu(1)
NONLINEAR DYNAMIC MODEL ON STEEL-WIRE ISOLATOR
BAN Shuhao, LI Xiaoyan, JIANG Xuedong, HU Aiping
Mechanics in Engineering    2012, 34 (1): 66-69.   DOI: 10.6052/1000-0879-20120112
Abstract1563)      PDF(pc) (1299KB)(717)       Save
A nonlinear dynamic model for the isolation system of steel-wire isolators is constructed with the introduction of a softened frequency coefficient based on static mechanical properties for steel-wire isolators. The dynamic responses to impulse and random vibrations of this system are investigated with the nonlinear dynamic model. The simulated results are discussed. The theoretical analyses and simulated results show that the nonlinear dynamic model with the softened frequency coefficient has a better isolation effect compared to the linear Hookean spring model.
Reference | Related Articles | Metrics
Cited: Baidu(4)
TOPOLOGICAL OPTIMIZATION FOR CONVEYOR LINK PLATE OF STRICKLE RECLAIMER WITH STRESS CONSTRAINTS UNDER MULTIPLE LOADING CASES
HUANG Fei, PENG Gaoming, HE Hao, SHI Limin
Mechanics in Engineering    2012, 34 (1): 70-74.   DOI: 10.6052/1000-0879-20120113
Abstract1340)      PDF(pc) (1549KB)(524)       Save
The ICM method is used to build topological optimization model for conveyor link plate of cantilever strickle reclaimer. A multiple-level and load magnification strategy was introduced to solve ill loading problem, which often occurs in topological optimization with stress constraint for continuum structure in multiple loads. Element's live and death method in ANSYS software associated with ICM method and multiple-level strategy are used to kill, reserve and resurge element. At last, topological optimization for conveyor link plate was accomplished, and light weight design was achieved through APDL in ANSYS.
Reference | Related Articles | Metrics
Cited: Baidu(2)
MECHANICAL BEHAVIOR OF COMPOSITE REPAIRED COMPONENTS UNDER CORROSION ENVIRONMENT
WANG Haowei, LIU Yuanhai, LIU Chengchen
Mechanics in Engineering    2012, 34 (1): 75-79,74.   DOI: 10.6052/1000-0879-20120114
Abstract1198)      PDF(pc) (1762KB)(645)       Save
The center cracked LY12CZ aluminum alloy plates were adhesively bonded with composite patches, and the tensile strength, the fatigue life and the crack growth during fatigue under air environment and accelerated pre-corrosion environment were investigated experimentally. The experimental results show that both the static strength and the fatigue life of the repaired aluminum substrates are significantly increased for the bonded composite patches, and the short-term pre-corrosion environment does not have a notable effect on the mechanical performance of composite repaired components. Also, a simple fatigue crack growth life prediction model, based on Paris formula and Rose's analytical solution, is proposed to predict the fatigue behavior of the repaired plates under air and pre-corrosion environments. The result shows a good quantitative agreement with experimental data.
Reference | Related Articles | Metrics
Cited: Baidu(1)
COMBINATORIAL OPTIMAL ALGORITHM FOR SENSOR ARRANGEMENT IN STRUCTURAL HEALTH MONITORING SYSTEM
LU Lingling, WANG Xi, HUANG Chenguang
Mechanics in Engineering    2012, 34 (1): 80-84,51.   DOI: 10.6052/1000-0879-20120115
Abstract1151)      PDF(pc) (1686KB)(686)       Save
In this paper, we present an effective optimization method of sensor arrangement for monitoring the dynamic response of thin flexible structures like plates and shells. The proposed method consists of genetic algorithm, modal kinetic energy and modal assurance criterion. A simplified wing structure is used to evaluate the effectiveness of the method. The numerical analysis and experimental results demonstrate that the proposed optimization algorithm can be used to determine effectively sensor arrangements. Firstly, the modal kinetic energy algorithm is used to catch the degree of freedom of the dynamic response of the structure with a large amplitude, and effectively improves the signal-noise ratio during the health monitoring. Secondly, the combination of genetic algorithm and modal assurance criterion can effectively ensure the independence of modal shapes, and provide more modal information of the structure, such as the modal frequency and the modal shape. The damage detection and the estimation of the residual life are more accurate and effective by using the proposed optimization method.
Reference | Related Articles | Metrics
Cited: Baidu(3)
A PRELIMINARY STUDY OF A NOVEL TWO-DIMENSION ELECTROMAGNETIC PARTICLE VELOCITY GAUGE UNDER DIVERGENT WAVE
WU Zutang, LI Jin, WANG Zhanjiang, ZHANG Jingsen, HUANG Xiaofei
Mechanics in Engineering    2012, 34 (1): 85-88,61.   DOI: 10.6052/1000-0879-20120116
Abstract849)      PDF(pc) (1515KB)(751)       Save
To study the electromagnetic test technique for the two-dimension particle velocity under divergent waves, a novel two-dimension electromagnetic particle velocity gauge configuration is designed based on the magnetic characteristic of Helmholtz coil under a pulse current. Its performance is verified through a comparison of the electromagnetic measurement between one-dimension and two-dimension particle velocities in PMMA. The experiment shows that it is efficient for the propagation measurement of divergent waves in an inhomogeneous medium even with interfaces, grooves and joints.
Reference | Related Articles | Metrics
  First page | Prev page | Next page | Last page Page 1 of 12, 346 records